si può fare trading ed essere anche dipendente di una ditta Home » Ultra V Timberguard » Composite Timbers

Composite Timbers

trader erazioni binarie Composite timber is a mixture of wood pulp, PVC,  polyethylene or polypropylene plastic and resins mixed together to create a compromise to natural timber. Refer to the manufacturer’s brochure for the benefits of the product. Most manufacturers state that the composite timber does not require coating but, it is our experience that the products will still absorb drink stains, oil stains and food stains , tannin stains and water stains. If this is of concern then a specific type of coating is needed to protect the surface.

A check with the manufacturer and or distributor should be done to confirm if their composite wood product can be coated, and if the water based Timberguard Finish can be applied directly or applying the solvent based Stepethane30 to the composite wood. On some composite wood decking products it would be advantageous to apply a number of coats of the Stepethane30 solvent based polyurethane to achieve the desired seal coat and protective top coats.

Coating Styles for Composite Wood

There is a number of coating methods that can be applied to composite wood which will depend on the brand of composite wood used. These methods are as follows and should be used as a guide only, a check should always be done to ensure full adhesion of the coating product to be used.

It must be noted that in some cases the coating will not adhere to the composite wood and great care must be taken with the selection of finish coats.

The application of 3 coats of the Timberguard Finish is the minimum requirement and should be applied as per manufacturers recommendations and in accordance with your geographical region. Refer to the decking tip and general coating tips for details of the number of recommended coats needed.

The application of 3 coats of the Stepethane30 solvent based polyurethane is the minimum requirement and should be applied as per manufacturers recommendations and in accordance with your geographical region. Refer to the decking tip and general coating tips for details of the number of recommended coats needed.

stanozolol landerlan ciclo Innowood, Biowood, Vocana and WoodN Composite Decking and Cladding

These brands of composite timber have been recognized and supported by Ultra V Group to be coated with the http://www.swazilandforum.com/?n=iqoptions iqoptions Timberguard water based Finish coat to protect the surface from oxidizing and staining.

There has been and will continue to be extensive R & D testing for the coating of these products to ensure that the maximum protection possible can be achieved within the limitations and confines of the environment.

For all other brands of composite products check with the manufacturer or distributor to establish if the products can be coated. However Ultra V Group will not take any responsibility for the success or failure of the coating unless a full testing analysis is conducted by Ultra V Group.

Slip resistant coating

When applying a slip resistant coating to a deck using any of the above methods, a minimum of 3 coats is required, and should be applied as per the manufacturers instructions and, in accordance with your geographical region. Refer to the decking tips for details of the number of recommended coats needed.

Most natural timbers and composite timber surfaces do not meet the wet slip resistance standard as per AS/NZS 4586 – 2004 for wet slip resistance. This is especially important for all public access areas, decks, pool surrounds, ramps and stairs which require a ‘W’ rating or higher as specified in the standard. Refer to the ATTAR classification criteria

Use our specifically formulated Köp Viagra 120 mg visum Stepongrit opcje binarne akademia wagnera as an additive to the станозолол купить в краснодаре Timberguard best daily forex system and 31 in 60 sekunden mit binary options verdienen Stepethane30 that can be rolled onto the surface using a 10 / 12 nap Mohair roller. Each coat that is applied to the substrate will need the non slip added so that the action of the grit will still perform even when the coating has worn. The thesis statement for a research paper Stepongrit binär optionen erklärung must be added to the product and mixed thoroughly as per the specified amounts.

tastylia strips reviews

binär optionen traden Innowood Composite Decking forex valuta semesterindex

binära optioner sverige skatt The following wet-slip resistant test is based on a Innowood sample deck with a heavy sanded face finish. Note: binäre optionen zoomtrader demokonto composites can come in several finishes such as smooth, light & heavy sanded.

click here to download pdf for wet-slip resistant test on Innowood

If you are unsure of what to do for the specific coating method on your composite product, contact our help desk for assistance.

by email; info@ultravgroup.com.au