Product Application

Application Instruction for New &  Old timber

The first and most important step to sealing your decking, timber and wall cladding is to choose the proper sealer. There are many different types of sealers on the market. The best one to use is the one that will afford the maximum protection and value, this is erfahrungen über binäre optionen Timberguard Finish Natural Tone. There are many companies who claim that their product will deliver what you need. Experience has taught us that a large percentage of these claims are false.

A good finish will have UV protection, mold and mildew resistant, and a life of several years. After cleaning the surface and allowing sufficient drying time you are ready to apply the primer followed by the finish coating. We recommend the use of an airless spray gun (minimum of 2 people required), flat lambs wool applicator, roller and paint brush for material application.


If you are going to use a airless spray gun on your timber cladding, louvres etc you must first apply plastic sheeting to all areas that you do not want overspray on, including walls, windows and plants. If you are going to use a flat lambs wool applicator for decking only then use 48mm masking tape around the edges of walls, pillars etc. Make sure that the masking tape is not sitting directly on the timber deck as this might cause some of the product to attach itself to the tape and could become damaged when the tape is removed. Next place tarps, or plastic sheeting, under the rails if they are to be coated and IMMEDIATELY remove any runs as these spots will dry darker that the rest of the deck. Once these spots dry it is nearly impossible to get them out.

Stir the product with a flat stirrer before use. Apply two or more coats with a brush, flat lambs wool applicator, roller

(10ml nap), airless spray gun (8 to 11 Thou tip) or air assisted spray gun.

First, apply 1 coat of the Timberguard Primer clear water based penetrating sealer to the timber and wait for 30 minutes to dry.

Now you are ready to apply the Timberguard Finish Natural Tone water based Polyurethane.

Apply the first coat so that you are always applying the product to a wet edge. Do not apply wet product to tacky or dried product as this will leave lap marks. Ensure that a good amount of product is applied to the end grain and edges, this is important to reduce any edge delaminating.

If you are using an airless spray gun, back brush or roll immediately the product is applied to the surface. This will ensure a better penetration and remove any excess pooling or runs of the product. Do not brush or roll if the product has started to tack off as this will cause the coating to prick up and reduce the adhesion of the coating. If this occurs wait until the product dries and give a light sand with 100 grit sand paper prior to the next coat.

When using a roller or lambs wool applicator, work max. of 3 boards at a time.

Apply the second and subsequent coats the same as the first coat. No sanding is required between coats. It is very important to re apply the second and additional coats as per the manufacturers drying recommendations and not before. The re coating time is a minimum of 2 hours @ 25° C


1st coat on dressed timber 12m²/litre, 2nd coat up to 14m²/litre. 8m²/litre for 1st coat and12m²/litre per subsequent coats on rough sawn timber. Coverage varies depending on the texture of the timber and application technique.

Drying Time

Touch dry in a few minutes @ 25°Celsius and re-coat in approx 2 hours depending on temperature, humidity and other weather conditions. Do not apply if the temperature is below 10°C or above 30°C during application or drying period.

Do not apply a coating to a hot substrate, wait until the substrate cools or is in shade.

If rain is imminent do not apply Timberguard. Coating Selection – “it couldn’t be easier”

One of the main advantages of using Natural Tone Timberguard, is that the one product will beautify & enhance all exterior timbers. You do not need a separate finish for Pine, Cedar, Merbau and all the other timbers in the market. Natural tone has been designed to make your choice simple & easy.

follow Natural Tone Matt finish for exterior timbers – is a specifically formulated coating that will enrich all natural timber species with a transparent oxide pigment. A brown milky product when wet and transparent clear matt finish when dry.

The Natural Tone finish is designed to enhance & highlight the natural tones of all timber species, giving the timber a rich exotic finish. The transparent oxide pigment further protects the timber from the effects of extreme UV exposure.

source site Natural Tone Gloss finish for exterior finishes – is a specifically formulated coating with a transparent oxide pigment. A brown milky product when wet and transparent clear gloss finish when dry.

Also available in source url Natural Clear Matt** sites de rencontres gratuits au canada and sugar daddies dating sites in nigeria Natural Clear Gloss.** A white milky product when wet and a clear gloss or matt finish when dry. Natural Clear provides a totally clear protection for timber, which can be used for go site interior/exterior applications, including composite timbers – see long life tips, decking & exterior timber.

click Select Natural Tone for all exterior applications where long life protection and minimal maintenance is needed and in areas of high UV exposure.

** For a solid colour finish Standard water based Universal Tinters can be added to the Clear gloss or Clear matt as per the Australian Standard AS2700 industrial coatings colour guide.

These tinters are readily available from paint stores and they can colour match to your specifications.

Remember that if you are choosing to use a solid colour and need to use more than 1 container, if possible mix the quantities together in a larger container to ensure the consistency of colour.

Download Ultra V Timberguard application instruction